{"dataType": "CVE_RECORD", "dataVersion": "5.1", "cveMetadata": {"cveId": "CVE-2025-39928", "assignerOrgId": "416baaa9-dc9f-4396-8d5f-8c081fb06d67", "state": "PUBLISHED", "assignerShortName": "Linux", "dateReserved": "2025-04-16T07:20:57.147Z", "datePublished": "2025-10-01T08:07:15.530Z", "dateUpdated": "2025-10-01T08:07:15.530Z"}, "containers": {"cna": {"providerMetadata": {"orgId": "416baaa9-dc9f-4396-8d5f-8c081fb06d67", "shortName": "Linux", "dateUpdated": "2025-10-01T08:07:15.530Z"}, "descriptions": [{"lang": "en", "value": "In the Linux kernel, the following vulnerability has been resolved:\n\ni2c: rtl9300: ensure data length is within supported range\n\nAdd an explicit check for the xfer length to 'rtl9300_i2c_config_xfer'\nto ensure the data length isn't within the supported range. In\nparticular a data length of 0 is not supported by the hardware and\ncauses unintended or destructive behaviour.\n\nThis limitation becomes obvious when looking at the register\ndocumentation [1]. 4 bits are reserved for DATA_WIDTH and the value\nof these 4 bits is used as N + 1, allowing a data length range of\n1 <= len <= 16.\n\nAffected by this is the SMBus Quick Operation which works with a data\nlength of 0. Passing 0 as the length causes an underflow of the value\ndue to:\n\n(len - 1) & 0xf\n\nand effectively specifying a transfer length of 16 via the registers.\nThis causes a 16-byte write operation instead of a Quick Write. For\nexample, on SFP modules without write-protected EEPROM this soft-bricks\nthem by overwriting some initial bytes.\n\nFor completeness, also add a quirk for the zero length.\n\n[1] https://svanheule.net/realtek/longan/register/i2c_mst1_ctrl2"}], "affected": [{"product": "Linux", "vendor": "Linux", "defaultStatus": "unaffected", "repo": "https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git", "programFiles": ["drivers/i2c/busses/i2c-rtl9300.c"], "versions": [{"version": "c366be720235301fdadf67e6f1ea6ff32669c074", "lessThan": "c91382328fc89f73144d5582f2d8f1dd3e41c8f7", "status": "affected", "versionType": "git"}, {"version": "c366be720235301fdadf67e6f1ea6ff32669c074", "lessThan": "06418cb5a1a542a003fdb4ad8e76ea542d57cfba", "status": "affected", "versionType": "git"}]}, {"product": "Linux", "vendor": "Linux", "defaultStatus": "affected", "repo": "https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git", "programFiles": ["drivers/i2c/busses/i2c-rtl9300.c"], "versions": [{"version": "6.13", "status": "affected"}, {"version": "0", "lessThan": "6.13", "status": "unaffected", "versionType": "semver"}, {"version": "6.16.8", "lessThanOrEqual": "6.16.*", "status": "unaffected", "versionType": "semver"}, {"version": "6.17", "lessThanOrEqual": "*", "status": "unaffected", "versionType": "original_commit_for_fix"}]}], "cpeApplicability": [{"nodes": [{"operator": "OR", "negate": false, "cpeMatch": [{"vulnerable": true, "criteria": "cpe:2.3:o:linux:linux_kernel:*:*:*:*:*:*:*:*", "versionStartIncluding": "6.13", "versionEndExcluding": "6.16.8"}, {"vulnerable": true, "criteria": "cpe:2.3:o:linux:linux_kernel:*:*:*:*:*:*:*:*", "versionStartIncluding": "6.13", "versionEndExcluding": "6.17"}]}]}], "references": [{"url": "https://git.kernel.org/stable/c/c91382328fc89f73144d5582f2d8f1dd3e41c8f7"}, {"url": "https://git.kernel.org/stable/c/06418cb5a1a542a003fdb4ad8e76ea542d57cfba"}], "title": "i2c: rtl9300: ensure data length is within supported range", "x_generator": {"engine": "bippy-1.2.0"}}}}

{}

{"configurations": [{"nodes": [{"cpeMatch": [{"criteria": "cpe:2.3:o:linux:linux_kernel:*:*:*:*:*:*:*:*", "matchCriteriaId": "8DA00A4E-AABB-4A69-AB39-67B22D0B36D2", "versionEndExcluding": "6.16.8", "versionStartIncluding": "6.13", "vulnerable": true}, {"criteria": "cpe:2.3:o:linux:linux_kernel:6.17:rc1:*:*:*:*:*:*", "matchCriteriaId": "327D22EF-390B-454C-BD31-2ED23C998A1C", "vulnerable": true}, {"criteria": "cpe:2.3:o:linux:linux_kernel:6.17:rc2:*:*:*:*:*:*", "matchCriteriaId": "C730CD9A-D969-4A8E-9522-162AAF7C0EE9", "vulnerable": true}, {"criteria": "cpe:2.3:o:linux:linux_kernel:6.17:rc3:*:*:*:*:*:*", "matchCriteriaId": "39982C4B-716E-4B2F-8196-FA301F47807D", "vulnerable": true}, {"criteria": "cpe:2.3:o:linux:linux_kernel:6.17:rc4:*:*:*:*:*:*", "matchCriteriaId": "340BEEA9-D70D-4290-B502-FBB1032353B1", "vulnerable": true}], "negate": false, "operator": "OR"}]}], "cveTags": [], "descriptions": [{"lang": "en", "value": "In the Linux kernel, the following vulnerability has been resolved:\n\ni2c: rtl9300: ensure data length is within supported range\n\nAdd an explicit check for the xfer length to 'rtl9300_i2c_config_xfer'\nto ensure the data length isn't within the supported range. In\nparticular a data length of 0 is not supported by the hardware and\ncauses unintended or destructive behaviour.\n\nThis limitation becomes obvious when looking at the register\ndocumentation [1]. 4 bits are reserved for DATA_WIDTH and the value\nof these 4 bits is used as N + 1, allowing a data length range of\n1 <= len <= 16.\n\nAffected by this is the SMBus Quick Operation which works with a data\nlength of 0. Passing 0 as the length causes an underflow of the value\ndue to:\n\n(len - 1) & 0xf\n\nand effectively specifying a transfer length of 16 via the registers.\nThis causes a 16-byte write operation instead of a Quick Write. For\nexample, on SFP modules without write-protected EEPROM this soft-bricks\nthem by overwriting some initial bytes.\n\nFor completeness, also add a quirk for the zero length.\n\n[1] https://svanheule.net/realtek/longan/register/i2c_mst1_ctrl2"}], "id": "CVE-2025-39928", "lastModified": "2025-12-10T21:50:13.647", "metrics": {"cvssMetricV31": [{"cvssData": {"attackComplexity": "LOW", "attackVector": "LOCAL", "availabilityImpact": "HIGH", "baseScore": 5.5, "baseSeverity": "MEDIUM", "confidentialityImpact": "NONE", "integrityImpact": "NONE", "privilegesRequired": "LOW", "scope": "UNCHANGED", "userInteraction": "NONE", "vectorString": "CVSS:3.1/AV:L/AC:L/PR:L/UI:N/S:U/C:N/I:N/A:H", "version": "3.1"}, "exploitabilityScore": 1.8, "impactScore": 3.6, "source": "nvd@nist.gov", "type": "Primary"}]}, "published": "2025-10-01T08:15:36.230", "references": [{"source": "416baaa9-dc9f-4396-8d5f-8c081fb06d67", "tags": ["Patch"], "url": "https://git.kernel.org/stable/c/06418cb5a1a542a003fdb4ad8e76ea542d57cfba"}, {"source": "416baaa9-dc9f-4396-8d5f-8c081fb06d67", "tags": ["Patch"], "url": "https://git.kernel.org/stable/c/c91382328fc89f73144d5582f2d8f1dd3e41c8f7"}], "sourceIdentifier": "416baaa9-dc9f-4396-8d5f-8c081fb06d67", "vulnStatus": "Analyzed", "weaknesses": [{"description": [{"lang": "en", "value": "CWE-191"}], "source": "nvd@nist.gov", "type": "Primary"}]}

{"bugzilla": {"description": "kernel: i2c: rtl9300: ensure data length is within supported range", "id": "2400626", "url": "https://bugzilla.redhat.com/show_bug.cgi?id=2400626"}, "csaw": false, "cvss3": {"cvss3_base_score": "5.5", "cvss3_scoring_vector": "CVSS:3.1/AV:L/AC:L/PR:L/UI:N/S:U/C:N/I:N/A:H", "status": "draft"}, "details": ["In the Linux kernel, the following vulnerability has been resolved:\ni2c: rtl9300: ensure data length is within supported range\nAdd an explicit check for the xfer length to 'rtl9300_i2c_config_xfer'\nto ensure the data length isn't within the supported range. In\nparticular a data length of 0 is not supported by the hardware and\ncauses unintended or destructive behaviour.\nThis limitation becomes obvious when looking at the register\ndocumentation [1]. 4 bits are reserved for DATA_WIDTH and the value\nof these 4 bits is used as N + 1, allowing a data length range of\n1 <= len <= 16.\nAffected by this is the SMBus Quick Operation which works with a data\nlength of 0. Passing 0 as the length causes an underflow of the value\ndue to:\n(len - 1) & 0xf\nand effectively specifying a transfer length of 16 via the registers.\nThis causes a 16-byte write operation instead of a Quick Write. For\nexample, on SFP modules without write-protected EEPROM this soft-bricks\nthem by overwriting some initial bytes.\nFor completeness, also add a quirk for the zero length.\n[1] https://svanheule.net/realtek/longan/register/i2c_mst1_ctrl2"], "name": "CVE-2025-39928", "package_state": [{"cpe": "cpe:/o:redhat:enterprise_linux:10", "fix_state": "Not affected", "package_name": "kernel", "product_name": "Red Hat Enterprise Linux 10"}, {"cpe": "cpe:/o:redhat:enterprise_linux:6", "fix_state": "Not affected", "package_name": "kernel", "product_name": "Red Hat Enterprise Linux 6"}, {"cpe": "cpe:/o:redhat:enterprise_linux:7", "fix_state": "Not affected", "package_name": "kernel", "product_name": "Red Hat Enterprise Linux 7"}, {"cpe": "cpe:/o:redhat:enterprise_linux:7", "fix_state": "Not affected", "package_name": "kernel-rt", "product_name": "Red Hat Enterprise Linux 7"}, {"cpe": "cpe:/o:redhat:enterprise_linux:8", "fix_state": "Not affected", "package_name": "kernel", "product_name": "Red Hat Enterprise Linux 8"}, {"cpe": "cpe:/o:redhat:enterprise_linux:8", "fix_state": "Not affected", "package_name": "kernel-rt", "product_name": "Red Hat Enterprise Linux 8"}, {"cpe": "cpe:/o:redhat:enterprise_linux:9", "fix_state": "Not affected", "package_name": "kernel", "product_name": "Red Hat Enterprise Linux 9"}, {"cpe": "cpe:/o:redhat:enterprise_linux:9", "fix_state": "Not affected", "package_name": "kernel-rt", "product_name": "Red Hat Enterprise Linux 9"}, {"cpe": "cpe:/o:redhat:rhivos:1", "fix_state": "Not affected", "package_name": "kernel", "product_name": "Red Hat In-Vehicle Operating System 1"}], "public_date": "2025-10-01T00:00:00Z", "references": ["https://www.cve.org/CVERecord?id=CVE-2025-39928\nhttps://nvd.nist.gov/vuln/detail/CVE-2025-39928\nhttps://lore.kernel.org/linux-cve-announce/2025100125-CVE-2025-39928-b66c@gregkh/T"], "threat_severity": "Moderate"}