Total
12879 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2022-48951 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: ASoC: ops: Check bounds for second channel in snd_soc_put_volsw_sx() The bounds checks in snd_soc_put_volsw_sx() are only being applied to the first channel, meaning it is possible to write out of bounds values to the second channel in stereo controls. Add appropriate checks. | ||||
| CVE-2022-48927 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: iio: adc: tsc2046: fix memory corruption by preventing array overflow On one side we have indio_dev->num_channels includes all physical channels + timestamp channel. On other side we have an array allocated only for physical channels. So, fix memory corruption by ARRAY_SIZE() instead of num_channels variable. Note the first case is a cleanup rather than a fix as the software timestamp channel bit in active_scanmask is never set by the IIO core. | ||||
| CVE-2022-48871 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: tty: serial: qcom-geni-serial: fix slab-out-of-bounds on RX FIFO buffer Driver's probe allocates memory for RX FIFO (port->rx_fifo) based on default RX FIFO depth, e.g. 16. Later during serial startup the qcom_geni_serial_port_setup() updates the RX FIFO depth (port->rx_fifo_depth) to match real device capabilities, e.g. to 32. The RX UART handle code will read "port->rx_fifo_depth" number of words into "port->rx_fifo" buffer, thus exceeding the bounds. This can be observed in certain configurations with Qualcomm Bluetooth HCI UART device and KASAN: Bluetooth: hci0: QCA Product ID :0x00000010 Bluetooth: hci0: QCA SOC Version :0x400a0200 Bluetooth: hci0: QCA ROM Version :0x00000200 Bluetooth: hci0: QCA Patch Version:0x00000d2b Bluetooth: hci0: QCA controller version 0x02000200 Bluetooth: hci0: QCA Downloading qca/htbtfw20.tlv bluetooth hci0: Direct firmware load for qca/htbtfw20.tlv failed with error -2 Bluetooth: hci0: QCA Failed to request file: qca/htbtfw20.tlv (-2) Bluetooth: hci0: QCA Failed to download patch (-2) ================================================================== BUG: KASAN: slab-out-of-bounds in handle_rx_uart+0xa8/0x18c Write of size 4 at addr ffff279347d578c0 by task swapper/0/0 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.1.0-rt5-00350-gb2450b7e00be-dirty #26 Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT) Call trace: dump_backtrace.part.0+0xe0/0xf0 show_stack+0x18/0x40 dump_stack_lvl+0x8c/0xb8 print_report+0x188/0x488 kasan_report+0xb4/0x100 __asan_store4+0x80/0xa4 handle_rx_uart+0xa8/0x18c qcom_geni_serial_handle_rx+0x84/0x9c qcom_geni_serial_isr+0x24c/0x760 __handle_irq_event_percpu+0x108/0x500 handle_irq_event+0x6c/0x110 handle_fasteoi_irq+0x138/0x2cc generic_handle_domain_irq+0x48/0x64 If the RX FIFO depth changes after probe, be sure to resize the buffer. | ||||
| CVE-2022-48847 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: watch_queue: Fix filter limit check In watch_queue_set_filter(), there are a couple of places where we check that the filter type value does not exceed what the type_filter bitmap can hold. One place calculates the number of bits by: if (tf[i].type >= sizeof(wfilter->type_filter) * 8) which is fine, but the second does: if (tf[i].type >= sizeof(wfilter->type_filter) * BITS_PER_LONG) which is not. This can lead to a couple of out-of-bounds writes due to a too-large type: (1) __set_bit() on wfilter->type_filter (2) Writing more elements in wfilter->filters[] than we allocated. Fix this by just using the proper WATCH_TYPE__NR instead, which is the number of types we actually know about. The bug may cause an oops looking something like: BUG: KASAN: slab-out-of-bounds in watch_queue_set_filter+0x659/0x740 Write of size 4 at addr ffff88800d2c66bc by task watch_queue_oob/611 ... Call Trace: <TASK> dump_stack_lvl+0x45/0x59 print_address_description.constprop.0+0x1f/0x150 ... kasan_report.cold+0x7f/0x11b ... watch_queue_set_filter+0x659/0x740 ... __x64_sys_ioctl+0x127/0x190 do_syscall_64+0x43/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae Allocated by task 611: kasan_save_stack+0x1e/0x40 __kasan_kmalloc+0x81/0xa0 watch_queue_set_filter+0x23a/0x740 __x64_sys_ioctl+0x127/0x190 do_syscall_64+0x43/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae The buggy address belongs to the object at ffff88800d2c66a0 which belongs to the cache kmalloc-32 of size 32 The buggy address is located 28 bytes inside of 32-byte region [ffff88800d2c66a0, ffff88800d2c66c0) | ||||
| CVE-2022-48627 | 3 Debian, Linux, Redhat | 4 Debian Linux, Linux Kernel, Enterprise Linux and 1 more | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: vt: fix memory overlapping when deleting chars in the buffer A memory overlapping copy occurs when deleting a long line. This memory overlapping copy can cause data corruption when scr_memcpyw is optimized to memcpy because memcpy does not ensure its behavior if the destination buffer overlaps with the source buffer. The line buffer is not always broken, because the memcpy utilizes the hardware acceleration, whose result is not deterministic. Fix this problem by using replacing the scr_memcpyw with scr_memmovew. | ||||
| CVE-2023-52916 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 6.7 Medium |
| In the Linux kernel, the following vulnerability has been resolved: media: aspeed: Fix memory overwrite if timing is 1600x900 When capturing 1600x900, system could crash when system memory usage is tight. The way to reproduce this issue: 1. Use 1600x900 to display on host 2. Mount ISO through 'Virtual media' on OpenBMC's web 3. Run script as below on host to do sha continuously #!/bin/bash while [ [1] ]; do find /media -type f -printf '"%h/%f"\n' | xargs sha256sum done 4. Open KVM on OpenBMC's web The size of macro block captured is 8x8. Therefore, we should make sure the height of src-buf is 8 aligned to fix this issue. | ||||
| CVE-2023-52829 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 6.2 Medium |
| In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: fix possible out-of-bound write in ath12k_wmi_ext_hal_reg_caps() reg_cap.phy_id is extracted from WMI event and could be an unexpected value in case some errors happen. As a result out-of-bound write may occur to soc->hal_reg_cap. Fix it by validating reg_cap.phy_id before using it. This is found during code review. Compile tested only. | ||||
| CVE-2023-52755 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 8.4 High |
| In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix slab out of bounds write in smb_inherit_dacl() slab out-of-bounds write is caused by that offsets is bigger than pntsd allocation size. This patch add the check to validate 3 offsets using allocation size. | ||||
| CVE-2023-52633 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.0 Medium |
| In the Linux kernel, the following vulnerability has been resolved: um: time-travel: fix time corruption In 'basic' time-travel mode (without =inf-cpu or =ext), we still get timer interrupts. These can happen at arbitrary points in time, i.e. while in timer_read(), which pushes time forward just a little bit. Then, if we happen to get the interrupt after calculating the new time to push to, but before actually finishing that, the interrupt will set the time to a value that's incompatible with the forward, and we'll crash because time goes backwards when we do the forwarding. Fix this by reading the time_travel_time, calculating the adjustment, and doing the adjustment all with interrupts disabled. | ||||
| CVE-2023-52628 | 2 Linux, Redhat | 3 Linux Kernel, Enterprise Linux, Rhel Eus | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: netfilter: nftables: exthdr: fix 4-byte stack OOB write If priv->len is a multiple of 4, then dst[len / 4] can write past the destination array which leads to stack corruption. This construct is necessary to clean the remainder of the register in case ->len is NOT a multiple of the register size, so make it conditional just like nft_payload.c does. The bug was added in 4.1 cycle and then copied/inherited when tcp/sctp and ip option support was added. Bug reported by Zero Day Initiative project (ZDI-CAN-21950, ZDI-CAN-21951, ZDI-CAN-21961). | ||||
| CVE-2023-52596 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: sysctl: Fix out of bounds access for empty sysctl registers When registering tables to the sysctl subsystem there is a check to see if header is a permanently empty directory (used for mounts). This check evaluates the first element of the ctl_table. This results in an out of bounds evaluation when registering empty directories. The function register_sysctl_mount_point now passes a ctl_table of size 1 instead of size 0. It now relies solely on the type to identify a permanently empty register. Make sure that the ctl_table has at least one element before testing for permanent emptiness. | ||||
| CVE-2023-52531 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: mvm: Fix a memory corruption issue A few lines above, space is kzalloc()'ed for: sizeof(struct iwl_nvm_data) + sizeof(struct ieee80211_channel) + sizeof(struct ieee80211_rate) 'mvm->nvm_data' is a 'struct iwl_nvm_data', so it is fine. At the end of this structure, there is the 'channels' flex array. Each element is of type 'struct ieee80211_channel'. So only 1 element is allocated in this array. When doing: mvm->nvm_data->bands[0].channels = mvm->nvm_data->channels; We point at the first element of the 'channels' flex array. So this is fine. However, when doing: mvm->nvm_data->bands[0].bitrates = (void *)((u8 *)mvm->nvm_data->channels + 1); because of the "(u8 *)" cast, we add only 1 to the address of the beginning of the flex array. It is likely that we want point at the 'struct ieee80211_rate' allocated just after. Remove the spurious casting so that the pointer arithmetic works as expected. | ||||
| CVE-2023-52512 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: pinctrl: nuvoton: wpcm450: fix out of bounds write Write into 'pctrl->gpio_bank' happens before the check for GPIO index validity, so out of bounds write may happen. Found by Linux Verification Center (linuxtesting.org) with SVACE. | ||||
| CVE-2023-52497 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 6.1 Medium |
| In the Linux kernel, the following vulnerability has been resolved: erofs: fix lz4 inplace decompression Currently EROFS can map another compressed buffer for inplace decompression, that was used to handle the cases that some pages of compressed data are actually not in-place I/O. However, like most simple LZ77 algorithms, LZ4 expects the compressed data is arranged at the end of the decompressed buffer and it explicitly uses memmove() to handle overlapping: __________________________________________________________ |_ direction of decompression --> ____ |_ compressed data _| Although EROFS arranges compressed data like this, it typically maps two individual virtual buffers so the relative order is uncertain. Previously, it was hardly observed since LZ4 only uses memmove() for short overlapped literals and x86/arm64 memmove implementations seem to completely cover it up and they don't have this issue. Juhyung reported that EROFS data corruption can be found on a new Intel x86 processor. After some analysis, it seems that recent x86 processors with the new FSRM feature expose this issue with "rep movsb". Let's strictly use the decompressed buffer for lz4 inplace decompression for now. Later, as an useful improvement, we could try to tie up these two buffers together in the correct order. | ||||
| CVE-2023-52495 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: soc: qcom: pmic_glink_altmode: fix port sanity check The PMIC GLINK altmode driver currently supports at most two ports. Fix the incomplete port sanity check on notifications to avoid accessing and corrupting memory beyond the port array if we ever get a notification for an unsupported port. | ||||
| CVE-2025-21966 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2025-05-04 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: dm-flakey: Fix memory corruption in optional corrupt_bio_byte feature Fix memory corruption due to incorrect parameter being passed to bio_init | ||||
| CVE-2025-21927 | 2 Linux, Redhat | 4 Linux Kernel, Enterprise Linux, Rhel E4s and 1 more | 2025-05-04 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: nvme-tcp: fix potential memory corruption in nvme_tcp_recv_pdu() nvme_tcp_recv_pdu() doesn't check the validity of the header length. When header digests are enabled, a target might send a packet with an invalid header length (e.g. 255), causing nvme_tcp_verify_hdgst() to access memory outside the allocated area and cause memory corruptions by overwriting it with the calculated digest. Fix this by rejecting packets with an unexpected header length. | ||||
| CVE-2025-21919 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2025-05-04 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: sched/fair: Fix potential memory corruption in child_cfs_rq_on_list child_cfs_rq_on_list attempts to convert a 'prev' pointer to a cfs_rq. This 'prev' pointer can originate from struct rq's leaf_cfs_rq_list, making the conversion invalid and potentially leading to memory corruption. Depending on the relative positions of leaf_cfs_rq_list and the task group (tg) pointer within the struct, this can cause a memory fault or access garbage data. The issue arises in list_add_leaf_cfs_rq, where both cfs_rq->leaf_cfs_rq_list and rq->leaf_cfs_rq_list are added to the same leaf list. Also, rq->tmp_alone_branch can be set to rq->leaf_cfs_rq_list. This adds a check `if (prev == &rq->leaf_cfs_rq_list)` after the main conditional in child_cfs_rq_on_list. This ensures that the container_of operation will convert a correct cfs_rq struct. This check is sufficient because only cfs_rqs on the same CPU are added to the list, so verifying the 'prev' pointer against the current rq's list head is enough. Fixes a potential memory corruption issue that due to current struct layout might not be manifesting as a crash but could lead to unpredictable behavior when the layout changes. | ||||
| CVE-2025-21865 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: gtp: Suppress list corruption splat in gtp_net_exit_batch_rtnl(). Brad Spengler reported the list_del() corruption splat in gtp_net_exit_batch_rtnl(). [0] Commit eb28fd76c0a0 ("gtp: Destroy device along with udp socket's netns dismantle.") added the for_each_netdev() loop in gtp_net_exit_batch_rtnl() to destroy devices in each netns as done in geneve and ip tunnels. However, this could trigger ->dellink() twice for the same device during ->exit_batch_rtnl(). Say we have two netns A & B and gtp device B that resides in netns B but whose UDP socket is in netns A. 1. cleanup_net() processes netns A and then B. 2. gtp_net_exit_batch_rtnl() finds the device B while iterating netns A's gn->gtp_dev_list and calls ->dellink(). [ device B is not yet unlinked from netns B as unregister_netdevice_many() has not been called. ] 3. gtp_net_exit_batch_rtnl() finds the device B while iterating netns B's for_each_netdev() and calls ->dellink(). gtp_dellink() cleans up the device's hash table, unlinks the dev from gn->gtp_dev_list, and calls unregister_netdevice_queue(). Basically, calling gtp_dellink() multiple times is fine unless CONFIG_DEBUG_LIST is enabled. Let's remove for_each_netdev() in gtp_net_exit_batch_rtnl() and delegate the destruction to default_device_exit_batch() as done in bareudp. [0]: list_del corruption, ffff8880aaa62c00->next (autoslab_size_M_dev_P_net_core_dev_11127_8_1328_8_S_4096_A_64_n_139+0xc00/0x1000 [slab object]) is LIST_POISON1 (ffffffffffffff02) (prev is 0xffffffffffffff04) kernel BUG at lib/list_debug.c:58! Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN CPU: 1 UID: 0 PID: 1804 Comm: kworker/u8:7 Tainted: G T 6.12.13-grsec-full-20250211091339 #1 Tainted: [T]=RANDSTRUCT Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Workqueue: netns cleanup_net RIP: 0010:[<ffffffff84947381>] __list_del_entry_valid_or_report+0x141/0x200 lib/list_debug.c:58 Code: c2 76 91 31 c0 e8 9f b1 f7 fc 0f 0b 4d 89 f0 48 c7 c1 02 ff ff ff 48 89 ea 48 89 ee 48 c7 c7 e0 c2 76 91 31 c0 e8 7f b1 f7 fc <0f> 0b 4d 89 e8 48 c7 c1 04 ff ff ff 48 89 ea 48 89 ee 48 c7 c7 60 RSP: 0018:fffffe8040b4fbd0 EFLAGS: 00010283 RAX: 00000000000000cc RBX: dffffc0000000000 RCX: ffffffff818c4054 RDX: ffffffff84947381 RSI: ffffffff818d1512 RDI: 0000000000000000 RBP: ffff8880aaa62c00 R08: 0000000000000001 R09: fffffbd008169f32 R10: fffffe8040b4f997 R11: 0000000000000001 R12: a1988d84f24943e4 R13: ffffffffffffff02 R14: ffffffffffffff04 R15: ffff8880aaa62c08 RBX: kasan shadow of 0x0 RCX: __wake_up_klogd.part.0+0x74/0xe0 kernel/printk/printk.c:4554 RDX: __list_del_entry_valid_or_report+0x141/0x200 lib/list_debug.c:58 RSI: vprintk+0x72/0x100 kernel/printk/printk_safe.c:71 RBP: autoslab_size_M_dev_P_net_core_dev_11127_8_1328_8_S_4096_A_64_n_139+0xc00/0x1000 [slab object] RSP: process kstack fffffe8040b4fbd0+0x7bd0/0x8000 [kworker/u8:7+netns 1804 ] R09: kasan shadow of process kstack fffffe8040b4f990+0x7990/0x8000 [kworker/u8:7+netns 1804 ] R10: process kstack fffffe8040b4f997+0x7997/0x8000 [kworker/u8:7+netns 1804 ] R15: autoslab_size_M_dev_P_net_core_dev_11127_8_1328_8_S_4096_A_64_n_139+0xc08/0x1000 [slab object] FS: 0000000000000000(0000) GS:ffff888116000000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000748f5372c000 CR3: 0000000015408000 CR4: 00000000003406f0 shadow CR4: 00000000003406f0 Stack: 0000000000000000 ffffffff8a0c35e7 ffffffff8a0c3603 ffff8880aaa62c00 ffff8880aaa62c00 0000000000000004 ffff88811145311c 0000000000000005 0000000000000001 ffff8880aaa62000 fffffe8040b4fd40 ffffffff8a0c360d Call Trace: <TASK> [<ffffffff8a0c360d>] __list_del_entry_valid include/linux/list.h:131 [inline] fffffe8040b4fc28 [<ffffffff8a0c360d>] __list_del_entry include/linux/list.h:248 [inline] fffffe8040b4fc28 [<ffffffff8a0c360d>] list_del include/linux/list.h:262 [inl ---truncated--- | ||||
| CVE-2025-21785 | 2 Linux, Redhat | 6 Linux Kernel, Enterprise Linux, Rhel Aus and 3 more | 2025-05-04 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: arm64: cacheinfo: Avoid out-of-bounds write to cacheinfo array The loop that detects/populates cache information already has a bounds check on the array size but does not account for cache levels with separate data/instructions cache. Fix this by incrementing the index for any populated leaf (instead of any populated level). | ||||