Total
506 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2023-52668 | 2024-12-19 | 5.5 Medium | ||
| In the Linux kernel, the following vulnerability has been resolved: btrfs: zoned: fix lock ordering in btrfs_zone_activate() The btrfs CI reported a lockdep warning as follows by running generic generic/129. WARNING: possible circular locking dependency detected 6.7.0-rc5+ #1 Not tainted ------------------------------------------------------ kworker/u5:5/793427 is trying to acquire lock: ffff88813256d028 (&cache->lock){+.+.}-{2:2}, at: btrfs_zone_finish_one_bg+0x5e/0x130 but task is already holding lock: ffff88810a23a318 (&fs_info->zone_active_bgs_lock){+.+.}-{2:2}, at: btrfs_zone_finish_one_bg+0x34/0x130 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&fs_info->zone_active_bgs_lock){+.+.}-{2:2}: ... -> #0 (&cache->lock){+.+.}-{2:2}: ... This is because we take fs_info->zone_active_bgs_lock after a block_group's lock in btrfs_zone_activate() while doing the opposite in other places. Fix the issue by expanding the fs_info->zone_active_bgs_lock's critical section and taking it before a block_group's lock. | ||||
| CVE-2023-52615 | 2 Linux, Redhat | 3 Linux Kernel, Enterprise Linux, Rhel Eus | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: hwrng: core - Fix page fault dead lock on mmap-ed hwrng There is a dead-lock in the hwrng device read path. This triggers when the user reads from /dev/hwrng into memory also mmap-ed from /dev/hwrng. The resulting page fault triggers a recursive read which then dead-locks. Fix this by using a stack buffer when calling copy_to_user. | ||||
| CVE-2023-52595 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: wifi: rt2x00: restart beacon queue when hardware reset When a hardware reset is triggered, all registers are reset, so all queues are forced to stop in hardware interface. However, mac80211 will not automatically stop the queue. If we don't manually stop the beacon queue, the queue will be deadlocked and unable to start again. This patch fixes the issue where Apple devices cannot connect to the AP after calling ieee80211_restart_hw(). | ||||
| CVE-2023-52516 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: dma-debug: don't call __dma_entry_alloc_check_leak() under free_entries_lock __dma_entry_alloc_check_leak() calls into printk -> serial console output (qcom geni) and grabs port->lock under free_entries_lock spin lock, which is a reverse locking dependency chain as qcom_geni IRQ handler can call into dma-debug code and grab free_entries_lock under port->lock. Move __dma_entry_alloc_check_leak() call out of free_entries_lock scope so that we don't acquire serial console's port->lock under it. Trimmed-down lockdep splat: The existing dependency chain (in reverse order) is: -> #2 (free_entries_lock){-.-.}-{2:2}: _raw_spin_lock_irqsave+0x60/0x80 dma_entry_alloc+0x38/0x110 debug_dma_map_page+0x60/0xf8 dma_map_page_attrs+0x1e0/0x230 dma_map_single_attrs.constprop.0+0x6c/0xc8 geni_se_rx_dma_prep+0x40/0xcc qcom_geni_serial_isr+0x310/0x510 __handle_irq_event_percpu+0x110/0x244 handle_irq_event_percpu+0x20/0x54 handle_irq_event+0x50/0x88 handle_fasteoi_irq+0xa4/0xcc handle_irq_desc+0x28/0x40 generic_handle_domain_irq+0x24/0x30 gic_handle_irq+0xc4/0x148 do_interrupt_handler+0xa4/0xb0 el1_interrupt+0x34/0x64 el1h_64_irq_handler+0x18/0x24 el1h_64_irq+0x64/0x68 arch_local_irq_enable+0x4/0x8 ____do_softirq+0x18/0x24 ... -> #1 (&port_lock_key){-.-.}-{2:2}: _raw_spin_lock_irqsave+0x60/0x80 qcom_geni_serial_console_write+0x184/0x1dc console_flush_all+0x344/0x454 console_unlock+0x94/0xf0 vprintk_emit+0x238/0x24c vprintk_default+0x3c/0x48 vprintk+0xb4/0xbc _printk+0x68/0x90 register_console+0x230/0x38c uart_add_one_port+0x338/0x494 qcom_geni_serial_probe+0x390/0x424 platform_probe+0x70/0xc0 really_probe+0x148/0x280 __driver_probe_device+0xfc/0x114 driver_probe_device+0x44/0x100 __device_attach_driver+0x64/0xdc bus_for_each_drv+0xb0/0xd8 __device_attach+0xe4/0x140 device_initial_probe+0x1c/0x28 bus_probe_device+0x44/0xb0 device_add+0x538/0x668 of_device_add+0x44/0x50 of_platform_device_create_pdata+0x94/0xc8 of_platform_bus_create+0x270/0x304 of_platform_populate+0xac/0xc4 devm_of_platform_populate+0x60/0xac geni_se_probe+0x154/0x160 platform_probe+0x70/0xc0 ... -> #0 (console_owner){-...}-{0:0}: __lock_acquire+0xdf8/0x109c lock_acquire+0x234/0x284 console_flush_all+0x330/0x454 console_unlock+0x94/0xf0 vprintk_emit+0x238/0x24c vprintk_default+0x3c/0x48 vprintk+0xb4/0xbc _printk+0x68/0x90 dma_entry_alloc+0xb4/0x110 debug_dma_map_sg+0xdc/0x2f8 __dma_map_sg_attrs+0xac/0xe4 dma_map_sgtable+0x30/0x4c get_pages+0x1d4/0x1e4 [msm] msm_gem_pin_pages_locked+0x38/0xac [msm] msm_gem_pin_vma_locked+0x58/0x88 [msm] msm_ioctl_gem_submit+0xde4/0x13ac [msm] drm_ioctl_kernel+0xe0/0x15c drm_ioctl+0x2e8/0x3f4 vfs_ioctl+0x30/0x50 ... Chain exists of: console_owner --> &port_lock_key --> free_entries_lock Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(free_entries_lock); lock(&port_lock_key); lock(free_entries_lock); lock(console_owner); *** DEADLOCK *** Call trace: dump_backtrace+0xb4/0xf0 show_stack+0x20/0x30 dump_stack_lvl+0x60/0x84 dump_stack+0x18/0x24 print_circular_bug+0x1cc/0x234 check_noncircular+0x78/0xac __lock_acquire+0xdf8/0x109c lock_acquire+0x234/0x284 console_flush_all+0x330/0x454 consol ---truncated--- | ||||
| CVE-2023-52498 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: PM: sleep: Fix possible deadlocks in core system-wide PM code It is reported that in low-memory situations the system-wide resume core code deadlocks, because async_schedule_dev() executes its argument function synchronously if it cannot allocate memory (and not only in that case) and that function attempts to acquire a mutex that is already held. Executing the argument function synchronously from within dpm_async_fn() may also be problematic for ordering reasons (it may cause a consumer device's resume callback to be invoked before a requisite supplier device's one, for example). Address this by changing the code in question to use async_schedule_dev_nocall() for scheduling the asynchronous execution of device suspend and resume functions and to directly run them synchronously if async_schedule_dev_nocall() returns false. | ||||
| CVE-2023-52493 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: bus: mhi: host: Drop chan lock before queuing buffers Ensure read and write locks for the channel are not taken in succession by dropping the read lock from parse_xfer_event() such that a callback given to client can potentially queue buffers and acquire the write lock in that process. Any queueing of buffers should be done without channel read lock acquired as it can result in multiple locks and a soft lockup. [mani: added fixes tag and cc'ed stable] | ||||
| CVE-2023-52484 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: iommu/arm-smmu-v3: Fix soft lockup triggered by arm_smmu_mm_invalidate_range When running an SVA case, the following soft lockup is triggered: -------------------------------------------------------------------- watchdog: BUG: soft lockup - CPU#244 stuck for 26s! pstate: 83400009 (Nzcv daif +PAN -UAO +TCO +DIT -SSBS BTYPE=--) pc : arm_smmu_cmdq_issue_cmdlist+0x178/0xa50 lr : arm_smmu_cmdq_issue_cmdlist+0x150/0xa50 sp : ffff8000d83ef290 x29: ffff8000d83ef290 x28: 000000003b9aca00 x27: 0000000000000000 x26: ffff8000d83ef3c0 x25: da86c0812194a0e8 x24: 0000000000000000 x23: 0000000000000040 x22: ffff8000d83ef340 x21: ffff0000c63980c0 x20: 0000000000000001 x19: ffff0000c6398080 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: ffff3000b4a3bbb0 x14: ffff3000b4a30888 x13: ffff3000b4a3cf60 x12: 0000000000000000 x11: 0000000000000000 x10: 0000000000000000 x9 : ffffc08120e4d6bc x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000048cfa x5 : 0000000000000000 x4 : 0000000000000001 x3 : 000000000000000a x2 : 0000000080000000 x1 : 0000000000000000 x0 : 0000000000000001 Call trace: arm_smmu_cmdq_issue_cmdlist+0x178/0xa50 __arm_smmu_tlb_inv_range+0x118/0x254 arm_smmu_tlb_inv_range_asid+0x6c/0x130 arm_smmu_mm_invalidate_range+0xa0/0xa4 __mmu_notifier_invalidate_range_end+0x88/0x120 unmap_vmas+0x194/0x1e0 unmap_region+0xb4/0x144 do_mas_align_munmap+0x290/0x490 do_mas_munmap+0xbc/0x124 __vm_munmap+0xa8/0x19c __arm64_sys_munmap+0x28/0x50 invoke_syscall+0x78/0x11c el0_svc_common.constprop.0+0x58/0x1c0 do_el0_svc+0x34/0x60 el0_svc+0x2c/0xd4 el0t_64_sync_handler+0x114/0x140 el0t_64_sync+0x1a4/0x1a8 -------------------------------------------------------------------- Note that since 6.6-rc1 the arm_smmu_mm_invalidate_range above is renamed to "arm_smmu_mm_arch_invalidate_secondary_tlbs", yet the problem remains. The commit 06ff87bae8d3 ("arm64: mm: remove unused functions and variable protoypes") fixed a similar lockup on the CPU MMU side. Yet, it can occur to SMMU too, since arm_smmu_mm_arch_invalidate_secondary_tlbs() is called typically next to MMU tlb flush function, e.g. tlb_flush_mmu_tlbonly { tlb_flush { __flush_tlb_range { // check MAX_TLBI_OPS } } mmu_notifier_arch_invalidate_secondary_tlbs { arm_smmu_mm_arch_invalidate_secondary_tlbs { // does not check MAX_TLBI_OPS } } } Clone a CMDQ_MAX_TLBI_OPS from the MAX_TLBI_OPS in tlbflush.h, since in an SVA case SMMU uses the CPU page table, so it makes sense to align with the tlbflush code. Then, replace per-page TLBI commands with a single per-asid TLBI command, if the request size hits this threshold. | ||||
| CVE-2023-52456 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: serial: imx: fix tx statemachine deadlock When using the serial port as RS485 port, the tx statemachine is used to control the RTS pin to drive the RS485 transceiver TX_EN pin. When the TTY port is closed in the middle of a transmission (for instance during userland application crash), imx_uart_shutdown disables the interface and disables the Transmission Complete interrupt. afer that, imx_uart_stop_tx bails on an incomplete transmission, to be retriggered by the TC interrupt. This interrupt is disabled and therefore the tx statemachine never transitions out of SEND. The statemachine is in deadlock now, and the TX_EN remains low, making the interface useless. imx_uart_stop_tx now checks for incomplete transmission AND whether TC interrupts are enabled before bailing to be retriggered. This makes sure the state machine handling is reached, and is properly set to WAIT_AFTER_SEND. | ||||
| CVE-2022-49018 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: mptcp: fix sleep in atomic at close time Matt reported a splat at msk close time: BUG: sleeping function called from invalid context at net/mptcp/protocol.c:2877 in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 155, name: packetdrill preempt_count: 201, expected: 0 RCU nest depth: 0, expected: 0 4 locks held by packetdrill/155: #0: ffff888001536990 (&sb->s_type->i_mutex_key#6){+.+.}-{3:3}, at: __sock_release (net/socket.c:650) #1: ffff88800b498130 (sk_lock-AF_INET){+.+.}-{0:0}, at: mptcp_close (net/mptcp/protocol.c:2973) #2: ffff88800b49a130 (sk_lock-AF_INET/1){+.+.}-{0:0}, at: __mptcp_close_ssk (net/mptcp/protocol.c:2363) #3: ffff88800b49a0b0 (slock-AF_INET){+...}-{2:2}, at: __lock_sock_fast (include/net/sock.h:1820) Preemption disabled at: 0x0 CPU: 1 PID: 155 Comm: packetdrill Not tainted 6.1.0-rc5 #365 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:107 (discriminator 4)) __might_resched.cold (kernel/sched/core.c:9891) __mptcp_destroy_sock (include/linux/kernel.h:110) __mptcp_close (net/mptcp/protocol.c:2959) mptcp_subflow_queue_clean (include/net/sock.h:1777) __mptcp_close_ssk (net/mptcp/protocol.c:2363) mptcp_destroy_common (net/mptcp/protocol.c:3170) mptcp_destroy (include/net/sock.h:1495) __mptcp_destroy_sock (net/mptcp/protocol.c:2886) __mptcp_close (net/mptcp/protocol.c:2959) mptcp_close (net/mptcp/protocol.c:2974) inet_release (net/ipv4/af_inet.c:432) __sock_release (net/socket.c:651) sock_close (net/socket.c:1367) __fput (fs/file_table.c:320) task_work_run (kernel/task_work.c:181 (discriminator 1)) exit_to_user_mode_prepare (include/linux/resume_user_mode.h:49) syscall_exit_to_user_mode (kernel/entry/common.c:130) do_syscall_64 (arch/x86/entry/common.c:87) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) We can't call mptcp_close under the 'fast' socket lock variant, replace it with a sock_lock_nested() as the relevant code is already under the listening msk socket lock protection. | ||||
| CVE-2022-48937 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 3.3 Low |
| In the Linux kernel, the following vulnerability has been resolved: io_uring: add a schedule point in io_add_buffers() Looping ~65535 times doing kmalloc() calls can trigger soft lockups, especially with DEBUG features (like KASAN). [ 253.536212] watchdog: BUG: soft lockup - CPU#64 stuck for 26s! [b219417889:12575] [ 253.544433] Modules linked in: vfat fat i2c_mux_pca954x i2c_mux spidev cdc_acm xhci_pci xhci_hcd sha3_generic gq(O) [ 253.544451] CPU: 64 PID: 12575 Comm: b219417889 Tainted: G S O 5.17.0-smp-DEV #801 [ 253.544457] RIP: 0010:kernel_text_address (./include/asm-generic/sections.h:192 ./include/linux/kallsyms.h:29 kernel/extable.c:67 kernel/extable.c:98) [ 253.544464] Code: 0f 93 c0 48 c7 c1 e0 63 d7 a4 48 39 cb 0f 92 c1 20 c1 0f b6 c1 5b 5d c3 90 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 53 48 89 fb <48> c7 c0 00 00 80 a0 41 be 01 00 00 00 48 39 c7 72 0c 48 c7 c0 40 [ 253.544468] RSP: 0018:ffff8882d8baf4c0 EFLAGS: 00000246 [ 253.544471] RAX: 1ffff1105b175e00 RBX: ffffffffa13ef09a RCX: 00000000a13ef001 [ 253.544474] RDX: ffffffffa13ef09a RSI: ffff8882d8baf558 RDI: ffffffffa13ef09a [ 253.544476] RBP: ffff8882d8baf4d8 R08: ffff8882d8baf5e0 R09: 0000000000000004 [ 253.544479] R10: ffff8882d8baf5e8 R11: ffffffffa0d59a50 R12: ffff8882eab20380 [ 253.544481] R13: ffffffffa0d59a50 R14: dffffc0000000000 R15: 1ffff1105b175eb0 [ 253.544483] FS: 00000000016d3380(0000) GS:ffff88af48c00000(0000) knlGS:0000000000000000 [ 253.544486] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 253.544488] CR2: 00000000004af0f0 CR3: 00000002eabfa004 CR4: 00000000003706e0 [ 253.544491] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 253.544492] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 253.544494] Call Trace: [ 253.544496] <TASK> [ 253.544498] ? io_queue_sqe (fs/io_uring.c:7143) [ 253.544505] __kernel_text_address (kernel/extable.c:78) [ 253.544508] unwind_get_return_address (arch/x86/kernel/unwind_frame.c:19) [ 253.544514] arch_stack_walk (arch/x86/kernel/stacktrace.c:27) [ 253.544517] ? io_queue_sqe (fs/io_uring.c:7143) [ 253.544521] stack_trace_save (kernel/stacktrace.c:123) [ 253.544527] ____kasan_kmalloc (mm/kasan/common.c:39 mm/kasan/common.c:45 mm/kasan/common.c:436 mm/kasan/common.c:515) [ 253.544531] ? ____kasan_kmalloc (mm/kasan/common.c:39 mm/kasan/common.c:45 mm/kasan/common.c:436 mm/kasan/common.c:515) [ 253.544533] ? __kasan_kmalloc (mm/kasan/common.c:524) [ 253.544535] ? kmem_cache_alloc_trace (./include/linux/kasan.h:270 mm/slab.c:3567) [ 253.544541] ? io_issue_sqe (fs/io_uring.c:4556 fs/io_uring.c:4589 fs/io_uring.c:6828) [ 253.544544] ? __io_queue_sqe (fs/io_uring.c:?) [ 253.544551] __kasan_kmalloc (mm/kasan/common.c:524) [ 253.544553] kmem_cache_alloc_trace (./include/linux/kasan.h:270 mm/slab.c:3567) [ 253.544556] ? io_issue_sqe (fs/io_uring.c:4556 fs/io_uring.c:4589 fs/io_uring.c:6828) [ 253.544560] io_issue_sqe (fs/io_uring.c:4556 fs/io_uring.c:4589 fs/io_uring.c:6828) [ 253.544564] ? __kasan_slab_alloc (mm/kasan/common.c:45 mm/kasan/common.c:436 mm/kasan/common.c:469) [ 253.544567] ? __kasan_slab_alloc (mm/kasan/common.c:39 mm/kasan/common.c:45 mm/kasan/common.c:436 mm/kasan/common.c:469) [ 253.544569] ? kmem_cache_alloc_bulk (mm/slab.h:732 mm/slab.c:3546) [ 253.544573] ? __io_alloc_req_refill (fs/io_uring.c:2078) [ 253.544578] ? io_submit_sqes (fs/io_uring.c:7441) [ 253.544581] ? __se_sys_io_uring_enter (fs/io_uring.c:10154 fs/io_uring.c:10096) [ 253.544584] ? __x64_sys_io_uring_enter (fs/io_uring.c:10096) [ 253.544587] ? do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) [ 253.544590] ? entry_SYSCALL_64_after_hwframe (??:?) [ 253.544596] __io_queue_sqe (fs/io_uring.c:?) [ 253.544600] io_queue_sqe (fs/io_uring.c:7143) [ 253.544603] io_submit_sqe (fs/io_uring.c:?) [ 253.544608] io_submit_sqes (fs/io_uring.c:?) [ 253.544612] __se_sys_io_uring_enter (fs/io_uring.c:10154 fs/io_uri ---truncated--- | ||||
| CVE-2022-48930 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: RDMA/ib_srp: Fix a deadlock Remove the flush_workqueue(system_long_wq) call since flushing system_long_wq is deadlock-prone and since that call is redundant with a preceding cancel_work_sync() | ||||
| CVE-2022-48920 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: btrfs: get rid of warning on transaction commit when using flushoncommit When using the flushoncommit mount option, during almost every transaction commit we trigger a warning from __writeback_inodes_sb_nr(): $ cat fs/fs-writeback.c: (...) static void __writeback_inodes_sb_nr(struct super_block *sb, ... { (...) WARN_ON(!rwsem_is_locked(&sb->s_umount)); (...) } (...) The trace produced in dmesg looks like the following: [947.473890] WARNING: CPU: 5 PID: 930 at fs/fs-writeback.c:2610 __writeback_inodes_sb_nr+0x7e/0xb3 [947.481623] Modules linked in: nfsd nls_cp437 cifs asn1_decoder cifs_arc4 fscache cifs_md4 ipmi_ssif [947.489571] CPU: 5 PID: 930 Comm: btrfs-transacti Not tainted 95.16.3-srb-asrock-00001-g36437ad63879 #186 [947.497969] RIP: 0010:__writeback_inodes_sb_nr+0x7e/0xb3 [947.502097] Code: 24 10 4c 89 44 24 18 c6 (...) [947.519760] RSP: 0018:ffffc90000777e10 EFLAGS: 00010246 [947.523818] RAX: 0000000000000000 RBX: 0000000000963300 RCX: 0000000000000000 [947.529765] RDX: 0000000000000000 RSI: 000000000000fa51 RDI: ffffc90000777e50 [947.535740] RBP: ffff888101628a90 R08: ffff888100955800 R09: ffff888100956000 [947.541701] R10: 0000000000000002 R11: 0000000000000001 R12: ffff888100963488 [947.547645] R13: ffff888100963000 R14: ffff888112fb7200 R15: ffff888100963460 [947.553621] FS: 0000000000000000(0000) GS:ffff88841fd40000(0000) knlGS:0000000000000000 [947.560537] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [947.565122] CR2: 0000000008be50c4 CR3: 000000000220c000 CR4: 00000000001006e0 [947.571072] Call Trace: [947.572354] <TASK> [947.573266] btrfs_commit_transaction+0x1f1/0x998 [947.576785] ? start_transaction+0x3ab/0x44e [947.579867] ? schedule_timeout+0x8a/0xdd [947.582716] transaction_kthread+0xe9/0x156 [947.585721] ? btrfs_cleanup_transaction.isra.0+0x407/0x407 [947.590104] kthread+0x131/0x139 [947.592168] ? set_kthread_struct+0x32/0x32 [947.595174] ret_from_fork+0x22/0x30 [947.597561] </TASK> [947.598553] ---[ end trace 644721052755541c ]--- This is because we started using writeback_inodes_sb() to flush delalloc when committing a transaction (when using -o flushoncommit), in order to avoid deadlocks with filesystem freeze operations. This change was made by commit ce8ea7cc6eb313 ("btrfs: don't call btrfs_start_delalloc_roots in flushoncommit"). After that change we started producing that warning, and every now and then a user reports this since the warning happens too often, it spams dmesg/syslog, and a user is unsure if this reflects any problem that might compromise the filesystem's reliability. We can not just lock the sb->s_umount semaphore before calling writeback_inodes_sb(), because that would at least deadlock with filesystem freezing, since at fs/super.c:freeze_super() sync_filesystem() is called while we are holding that semaphore in write mode, and that can trigger a transaction commit, resulting in a deadlock. It would also trigger the same type of deadlock in the unmount path. Possibly, it could also introduce some other locking dependencies that lockdep would report. To fix this call try_to_writeback_inodes_sb() instead of writeback_inodes_sb(), because that will try to read lock sb->s_umount and then will only call writeback_inodes_sb() if it was able to lock it. This is fine because the cases where it can't read lock sb->s_umount are during a filesystem unmount or during a filesystem freeze - in those cases sb->s_umount is write locked and sync_filesystem() is called, which calls writeback_inodes_sb(). In other words, in all cases where we can't take a read lock on sb->s_umount, writeback is already being triggered elsewhere. An alternative would be to call btrfs_start_delalloc_roots() with a number of pages different from LONG_MAX, for example matching the number of delalloc bytes we currently have, in ---truncated--- | ||||
| CVE-2022-48842 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 4.7 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ice: Fix race condition during interface enslave Commit 5dbbbd01cbba83 ("ice: Avoid RTNL lock when re-creating auxiliary device") changes a process of re-creation of aux device so ice_plug_aux_dev() is called from ice_service_task() context. This unfortunately opens a race window that can result in dead-lock when interface has left LAG and immediately enters LAG again. Reproducer: ``` #!/bin/sh ip link add lag0 type bond mode 1 miimon 100 ip link set lag0 for n in {1..10}; do echo Cycle: $n ip link set ens7f0 master lag0 sleep 1 ip link set ens7f0 nomaster done ``` This results in: [20976.208697] Workqueue: ice ice_service_task [ice] [20976.213422] Call Trace: [20976.215871] __schedule+0x2d1/0x830 [20976.219364] schedule+0x35/0xa0 [20976.222510] schedule_preempt_disabled+0xa/0x10 [20976.227043] __mutex_lock.isra.7+0x310/0x420 [20976.235071] enum_all_gids_of_dev_cb+0x1c/0x100 [ib_core] [20976.251215] ib_enum_roce_netdev+0xa4/0xe0 [ib_core] [20976.256192] ib_cache_setup_one+0x33/0xa0 [ib_core] [20976.261079] ib_register_device+0x40d/0x580 [ib_core] [20976.266139] irdma_ib_register_device+0x129/0x250 [irdma] [20976.281409] irdma_probe+0x2c1/0x360 [irdma] [20976.285691] auxiliary_bus_probe+0x45/0x70 [20976.289790] really_probe+0x1f2/0x480 [20976.298509] driver_probe_device+0x49/0xc0 [20976.302609] bus_for_each_drv+0x79/0xc0 [20976.306448] __device_attach+0xdc/0x160 [20976.310286] bus_probe_device+0x9d/0xb0 [20976.314128] device_add+0x43c/0x890 [20976.321287] __auxiliary_device_add+0x43/0x60 [20976.325644] ice_plug_aux_dev+0xb2/0x100 [ice] [20976.330109] ice_service_task+0xd0c/0xed0 [ice] [20976.342591] process_one_work+0x1a7/0x360 [20976.350536] worker_thread+0x30/0x390 [20976.358128] kthread+0x10a/0x120 [20976.365547] ret_from_fork+0x1f/0x40 ... [20976.438030] task:ip state:D stack: 0 pid:213658 ppid:213627 flags:0x00004084 [20976.446469] Call Trace: [20976.448921] __schedule+0x2d1/0x830 [20976.452414] schedule+0x35/0xa0 [20976.455559] schedule_preempt_disabled+0xa/0x10 [20976.460090] __mutex_lock.isra.7+0x310/0x420 [20976.464364] device_del+0x36/0x3c0 [20976.467772] ice_unplug_aux_dev+0x1a/0x40 [ice] [20976.472313] ice_lag_event_handler+0x2a2/0x520 [ice] [20976.477288] notifier_call_chain+0x47/0x70 [20976.481386] __netdev_upper_dev_link+0x18b/0x280 [20976.489845] bond_enslave+0xe05/0x1790 [bonding] [20976.494475] do_setlink+0x336/0xf50 [20976.502517] __rtnl_newlink+0x529/0x8b0 [20976.543441] rtnl_newlink+0x43/0x60 [20976.546934] rtnetlink_rcv_msg+0x2b1/0x360 [20976.559238] netlink_rcv_skb+0x4c/0x120 [20976.563079] netlink_unicast+0x196/0x230 [20976.567005] netlink_sendmsg+0x204/0x3d0 [20976.570930] sock_sendmsg+0x4c/0x50 [20976.574423] ____sys_sendmsg+0x1eb/0x250 [20976.586807] ___sys_sendmsg+0x7c/0xc0 [20976.606353] __sys_sendmsg+0x57/0xa0 [20976.609930] do_syscall_64+0x5b/0x1a0 [20976.613598] entry_SYSCALL_64_after_hwframe+0x65/0xca 1. Command 'ip link ... set nomaster' causes that ice_plug_aux_dev() is called from ice_service_task() context, aux device is created and associated device->lock is taken. 2. Command 'ip link ... set master...' calls ice's notifier under RTNL lock and that notifier calls ice_unplug_aux_dev(). That function tries to take aux device->lock but this is already taken by ice_plug_aux_dev() in step 1 3. Later ice_plug_aux_dev() tries to take RTNL lock but this is already taken in step 2 4. Dead-lock The patch fixes this issue by following changes: - Bit ICE_FLAG_PLUG_AUX_DEV is kept to be set during ice_plug_aux_dev() call in ice_service_task() - The bit is checked in ice_clear_rdma_cap() and only if it is not set then ice_unplug_aux_dev() is called. If it is set (in other words plugging of aux device was requested and ice_plug_aux_dev() is potentially running) then the function only clears the ---truncated--- | ||||
| CVE-2022-48826 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: drm/vc4: Fix deadlock on DSI device attach error DSI device attach to DSI host will be done with host device's lock held. Un-registering host in "device attach" error path (ex: probe retry) will result in deadlock with below call trace and non operational DSI display. Startup Call trace: [ 35.043036] rt_mutex_slowlock.constprop.21+0x184/0x1b8 [ 35.043048] mutex_lock_nested+0x7c/0xc8 [ 35.043060] device_del+0x4c/0x3e8 [ 35.043075] device_unregister+0x20/0x40 [ 35.043082] mipi_dsi_remove_device_fn+0x18/0x28 [ 35.043093] device_for_each_child+0x68/0xb0 [ 35.043105] mipi_dsi_host_unregister+0x40/0x90 [ 35.043115] vc4_dsi_host_attach+0xf0/0x120 [vc4] [ 35.043199] mipi_dsi_attach+0x30/0x48 [ 35.043209] tc358762_probe+0x128/0x164 [tc358762] [ 35.043225] mipi_dsi_drv_probe+0x28/0x38 [ 35.043234] really_probe+0xc0/0x318 [ 35.043244] __driver_probe_device+0x80/0xe8 [ 35.043254] driver_probe_device+0xb8/0x118 [ 35.043263] __device_attach_driver+0x98/0xe8 [ 35.043273] bus_for_each_drv+0x84/0xd8 [ 35.043281] __device_attach+0xf0/0x150 [ 35.043290] device_initial_probe+0x1c/0x28 [ 35.043300] bus_probe_device+0xa4/0xb0 [ 35.043308] deferred_probe_work_func+0xa0/0xe0 [ 35.043318] process_one_work+0x254/0x700 [ 35.043330] worker_thread+0x4c/0x448 [ 35.043339] kthread+0x19c/0x1a8 [ 35.043348] ret_from_fork+0x10/0x20 Shutdown Call trace: [ 365.565417] Call trace: [ 365.565423] __switch_to+0x148/0x200 [ 365.565452] __schedule+0x340/0x9c8 [ 365.565467] schedule+0x48/0x110 [ 365.565479] schedule_timeout+0x3b0/0x448 [ 365.565496] wait_for_completion+0xac/0x138 [ 365.565509] __flush_work+0x218/0x4e0 [ 365.565523] flush_work+0x1c/0x28 [ 365.565536] wait_for_device_probe+0x68/0x158 [ 365.565550] device_shutdown+0x24/0x348 [ 365.565561] kernel_restart_prepare+0x40/0x50 [ 365.565578] kernel_restart+0x20/0x70 [ 365.565591] __do_sys_reboot+0x10c/0x220 [ 365.565605] __arm64_sys_reboot+0x2c/0x38 [ 365.565619] invoke_syscall+0x4c/0x110 [ 365.565634] el0_svc_common.constprop.3+0xfc/0x120 [ 365.565648] do_el0_svc+0x2c/0x90 [ 365.565661] el0_svc+0x4c/0xf0 [ 365.565671] el0t_64_sync_handler+0x90/0xb8 [ 365.565682] el0t_64_sync+0x180/0x184 | ||||
| CVE-2022-48800 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: mm: vmscan: remove deadlock due to throttling failing to make progress A soft lockup bug in kcompactd was reported in a private bugzilla with the following visible in dmesg; watchdog: BUG: soft lockup - CPU#33 stuck for 26s! [kcompactd0:479] watchdog: BUG: soft lockup - CPU#33 stuck for 52s! [kcompactd0:479] watchdog: BUG: soft lockup - CPU#33 stuck for 78s! [kcompactd0:479] watchdog: BUG: soft lockup - CPU#33 stuck for 104s! [kcompactd0:479] The machine had 256G of RAM with no swap and an earlier failed allocation indicated that node 0 where kcompactd was run was potentially unreclaimable; Node 0 active_anon:29355112kB inactive_anon:2913528kB active_file:0kB inactive_file:0kB unevictable:64kB isolated(anon):0kB isolated(file):0kB mapped:8kB dirty:0kB writeback:0kB shmem:26780kB shmem_thp: 0kB shmem_pmdmapped: 0kB anon_thp: 23480320kB writeback_tmp:0kB kernel_stack:2272kB pagetables:24500kB all_unreclaimable? yes Vlastimil Babka investigated a crash dump and found that a task migrating pages was trying to drain PCP lists; PID: 52922 TASK: ffff969f820e5000 CPU: 19 COMMAND: "kworker/u128:3" Call Trace: __schedule schedule schedule_timeout wait_for_completion __flush_work __drain_all_pages __alloc_pages_slowpath.constprop.114 __alloc_pages alloc_migration_target migrate_pages migrate_to_node do_migrate_pages cpuset_migrate_mm_workfn process_one_work worker_thread kthread ret_from_fork This failure is specific to CONFIG_PREEMPT=n builds. The root of the problem is that kcompact0 is not rescheduling on a CPU while a task that has isolated a large number of the pages from the LRU is waiting on kcompact0 to reschedule so the pages can be released. While shrink_inactive_list() only loops once around too_many_isolated, reclaim can continue without rescheduling if sc->skipped_deactivate == 1 which could happen if there was no file LRU and the inactive anon list was not low. | ||||
| CVE-2022-48734 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: btrfs: fix deadlock between quota disable and qgroup rescan worker Quota disable ioctl starts a transaction before waiting for the qgroup rescan worker completes. However, this wait can be infinite and results in deadlock because of circular dependency among the quota disable ioctl, the qgroup rescan worker and the other task with transaction such as block group relocation task. The deadlock happens with the steps following: 1) Task A calls ioctl to disable quota. It starts a transaction and waits for qgroup rescan worker completes. 2) Task B such as block group relocation task starts a transaction and joins to the transaction that task A started. Then task B commits to the transaction. In this commit, task B waits for a commit by task A. 3) Task C as the qgroup rescan worker starts its job and starts a transaction. In this transaction start, task C waits for completion of the transaction that task A started and task B committed. This deadlock was found with fstests test case btrfs/115 and a zoned null_blk device. The test case enables and disables quota, and the block group reclaim was triggered during the quota disable by chance. The deadlock was also observed by running quota enable and disable in parallel with 'btrfs balance' command on regular null_blk devices. An example report of the deadlock: [372.469894] INFO: task kworker/u16:6:103 blocked for more than 122 seconds. [372.479944] Not tainted 5.16.0-rc8 #7 [372.485067] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [372.493898] task:kworker/u16:6 state:D stack: 0 pid: 103 ppid: 2 flags:0x00004000 [372.503285] Workqueue: btrfs-qgroup-rescan btrfs_work_helper [btrfs] [372.510782] Call Trace: [372.514092] <TASK> [372.521684] __schedule+0xb56/0x4850 [372.530104] ? io_schedule_timeout+0x190/0x190 [372.538842] ? lockdep_hardirqs_on+0x7e/0x100 [372.547092] ? _raw_spin_unlock_irqrestore+0x3e/0x60 [372.555591] schedule+0xe0/0x270 [372.561894] btrfs_commit_transaction+0x18bb/0x2610 [btrfs] [372.570506] ? btrfs_apply_pending_changes+0x50/0x50 [btrfs] [372.578875] ? free_unref_page+0x3f2/0x650 [372.585484] ? finish_wait+0x270/0x270 [372.591594] ? release_extent_buffer+0x224/0x420 [btrfs] [372.599264] btrfs_qgroup_rescan_worker+0xc13/0x10c0 [btrfs] [372.607157] ? lock_release+0x3a9/0x6d0 [372.613054] ? btrfs_qgroup_account_extent+0xda0/0xda0 [btrfs] [372.620960] ? do_raw_spin_lock+0x11e/0x250 [372.627137] ? rwlock_bug.part.0+0x90/0x90 [372.633215] ? lock_is_held_type+0xe4/0x140 [372.639404] btrfs_work_helper+0x1ae/0xa90 [btrfs] [372.646268] process_one_work+0x7e9/0x1320 [372.652321] ? lock_release+0x6d0/0x6d0 [372.658081] ? pwq_dec_nr_in_flight+0x230/0x230 [372.664513] ? rwlock_bug.part.0+0x90/0x90 [372.670529] worker_thread+0x59e/0xf90 [372.676172] ? process_one_work+0x1320/0x1320 [372.682440] kthread+0x3b9/0x490 [372.687550] ? _raw_spin_unlock_irq+0x24/0x50 [372.693811] ? set_kthread_struct+0x100/0x100 [372.700052] ret_from_fork+0x22/0x30 [372.705517] </TASK> [372.709747] INFO: task btrfs-transacti:2347 blocked for more than 123 seconds. [372.729827] Not tainted 5.16.0-rc8 #7 [372.745907] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [372.767106] task:btrfs-transacti state:D stack: 0 pid: 2347 ppid: 2 flags:0x00004000 [372.787776] Call Trace: [372.801652] <TASK> [372.812961] __schedule+0xb56/0x4850 [372.830011] ? io_schedule_timeout+0x190/0x190 [372.852547] ? lockdep_hardirqs_on+0x7e/0x100 [372.871761] ? _raw_spin_unlock_irqrestore+0x3e/0x60 [372.886792] schedule+0xe0/0x270 [372.901685] wait_current_trans+0x22c/0x310 [btrfs] [372.919743] ? btrfs_put_transaction+0x3d0/0x3d0 [btrfs] [372.938923] ? finish_wait+0x270/0x270 [372.959085] ? join_transaction+0xc7 ---truncated--- | ||||
| CVE-2022-48719 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: net, neigh: Do not trigger immediate probes on NUD_FAILED from neigh_managed_work syzkaller was able to trigger a deadlock for NTF_MANAGED entries [0]: kworker/0:16/14617 is trying to acquire lock: ffffffff8d4dd370 (&tbl->lock){++-.}-{2:2}, at: ___neigh_create+0x9e1/0x2990 net/core/neighbour.c:652 [...] but task is already holding lock: ffffffff8d4dd370 (&tbl->lock){++-.}-{2:2}, at: neigh_managed_work+0x35/0x250 net/core/neighbour.c:1572 The neighbor entry turned to NUD_FAILED state, where __neigh_event_send() triggered an immediate probe as per commit cd28ca0a3dd1 ("neigh: reduce arp latency") via neigh_probe() given table lock was held. One option to fix this situation is to defer the neigh_probe() back to the neigh_timer_handler() similarly as pre cd28ca0a3dd1. For the case of NTF_MANAGED, this deferral is acceptable given this only happens on actual failure state and regular / expected state is NUD_VALID with the entry already present. The fix adds a parameter to __neigh_event_send() in order to communicate whether immediate probe is allowed or disallowed. Existing call-sites of neigh_event_send() default as-is to immediate probe. However, the neigh_managed_work() disables it via use of neigh_event_send_probe(). [0] <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_deadlock_bug kernel/locking/lockdep.c:2956 [inline] check_deadlock kernel/locking/lockdep.c:2999 [inline] validate_chain kernel/locking/lockdep.c:3788 [inline] __lock_acquire.cold+0x149/0x3ab kernel/locking/lockdep.c:5027 lock_acquire kernel/locking/lockdep.c:5639 [inline] lock_acquire+0x1ab/0x510 kernel/locking/lockdep.c:5604 __raw_write_lock_bh include/linux/rwlock_api_smp.h:202 [inline] _raw_write_lock_bh+0x2f/0x40 kernel/locking/spinlock.c:334 ___neigh_create+0x9e1/0x2990 net/core/neighbour.c:652 ip6_finish_output2+0x1070/0x14f0 net/ipv6/ip6_output.c:123 __ip6_finish_output net/ipv6/ip6_output.c:191 [inline] __ip6_finish_output+0x61e/0xe90 net/ipv6/ip6_output.c:170 ip6_finish_output+0x32/0x200 net/ipv6/ip6_output.c:201 NF_HOOK_COND include/linux/netfilter.h:296 [inline] ip6_output+0x1e4/0x530 net/ipv6/ip6_output.c:224 dst_output include/net/dst.h:451 [inline] NF_HOOK include/linux/netfilter.h:307 [inline] ndisc_send_skb+0xa99/0x17f0 net/ipv6/ndisc.c:508 ndisc_send_ns+0x3a9/0x840 net/ipv6/ndisc.c:650 ndisc_solicit+0x2cd/0x4f0 net/ipv6/ndisc.c:742 neigh_probe+0xc2/0x110 net/core/neighbour.c:1040 __neigh_event_send+0x37d/0x1570 net/core/neighbour.c:1201 neigh_event_send include/net/neighbour.h:470 [inline] neigh_managed_work+0x162/0x250 net/core/neighbour.c:1574 process_one_work+0x9ac/0x1650 kernel/workqueue.c:2307 worker_thread+0x657/0x1110 kernel/workqueue.c:2454 kthread+0x2e9/0x3a0 kernel/kthread.c:377 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295 </TASK> | ||||
| CVE-2022-48675 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: IB/core: Fix a nested dead lock as part of ODP flow Fix a nested dead lock as part of ODP flow by using mmput_async(). From the below call trace [1] can see that calling mmput() once we have the umem_odp->umem_mutex locked as required by ib_umem_odp_map_dma_and_lock() might trigger in the same task the exit_mmap()->__mmu_notifier_release()->mlx5_ib_invalidate_range() which may dead lock when trying to lock the same mutex. Moving to use mmput_async() will solve the problem as the above exit_mmap() flow will be called in other task and will be executed once the lock will be available. [1] [64843.077665] task:kworker/u133:2 state:D stack: 0 pid:80906 ppid: 2 flags:0x00004000 [64843.077672] Workqueue: mlx5_ib_page_fault mlx5_ib_eqe_pf_action [mlx5_ib] [64843.077719] Call Trace: [64843.077722] <TASK> [64843.077724] __schedule+0x23d/0x590 [64843.077729] schedule+0x4e/0xb0 [64843.077735] schedule_preempt_disabled+0xe/0x10 [64843.077740] __mutex_lock.constprop.0+0x263/0x490 [64843.077747] __mutex_lock_slowpath+0x13/0x20 [64843.077752] mutex_lock+0x34/0x40 [64843.077758] mlx5_ib_invalidate_range+0x48/0x270 [mlx5_ib] [64843.077808] __mmu_notifier_release+0x1a4/0x200 [64843.077816] exit_mmap+0x1bc/0x200 [64843.077822] ? walk_page_range+0x9c/0x120 [64843.077828] ? __cond_resched+0x1a/0x50 [64843.077833] ? mutex_lock+0x13/0x40 [64843.077839] ? uprobe_clear_state+0xac/0x120 [64843.077860] mmput+0x5f/0x140 [64843.077867] ib_umem_odp_map_dma_and_lock+0x21b/0x580 [ib_core] [64843.077931] pagefault_real_mr+0x9a/0x140 [mlx5_ib] [64843.077962] pagefault_mr+0xb4/0x550 [mlx5_ib] [64843.077992] pagefault_single_data_segment.constprop.0+0x2ac/0x560 [mlx5_ib] [64843.078022] mlx5_ib_eqe_pf_action+0x528/0x780 [mlx5_ib] [64843.078051] process_one_work+0x22b/0x3d0 [64843.078059] worker_thread+0x53/0x410 [64843.078065] ? process_one_work+0x3d0/0x3d0 [64843.078073] kthread+0x12a/0x150 [64843.078079] ? set_kthread_struct+0x50/0x50 [64843.078085] ret_from_fork+0x22/0x30 [64843.078093] </TASK> | ||||
| CVE-2022-48671 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: cgroup: Add missing cpus_read_lock() to cgroup_attach_task_all() syzbot is hitting percpu_rwsem_assert_held(&cpu_hotplug_lock) warning at cpuset_attach() [1], for commit 4f7e7236435ca0ab ("cgroup: Fix threadgroup_rwsem <-> cpus_read_lock() deadlock") missed that cpuset_attach() is also called from cgroup_attach_task_all(). Add cpus_read_lock() like what cgroup_procs_write_start() does. | ||||
| CVE-2021-47622 | 1 Linux | 1 Linux Kernel | 2024-12-19 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: Fix a deadlock in the error handler The following deadlock has been observed on a test setup: - All tags allocated - The SCSI error handler calls ufshcd_eh_host_reset_handler() - ufshcd_eh_host_reset_handler() queues work that calls ufshcd_err_handler() - ufshcd_err_handler() locks up as follows: Workqueue: ufs_eh_wq_0 ufshcd_err_handler.cfi_jt Call trace: __switch_to+0x298/0x5d8 __schedule+0x6cc/0xa94 schedule+0x12c/0x298 blk_mq_get_tag+0x210/0x480 __blk_mq_alloc_request+0x1c8/0x284 blk_get_request+0x74/0x134 ufshcd_exec_dev_cmd+0x68/0x640 ufshcd_verify_dev_init+0x68/0x35c ufshcd_probe_hba+0x12c/0x1cb8 ufshcd_host_reset_and_restore+0x88/0x254 ufshcd_reset_and_restore+0xd0/0x354 ufshcd_err_handler+0x408/0xc58 process_one_work+0x24c/0x66c worker_thread+0x3e8/0xa4c kthread+0x150/0x1b4 ret_from_fork+0x10/0x30 Fix this lockup by making ufshcd_exec_dev_cmd() allocate a reserved request. | ||||